Product ID:ELVACITE 2013 ACRYLIC RESIN
MSDS Date:02/11/1991
FSC:8040
NIIN:00N036831
MSDS Number: BRDRL

Emergency Phone: 800-441-3637;800-424-9300(CHEMTREC)

Info Phone: 800-441-7515;302-999-4615

Preparer: F. M. LOGULLO

Cage: B0589

Telephone: 800-441-7515;800-441-9442

Cage: 18873

POLY (METHYL METHACRYLATE/N-BUTYL METHACRYLATE)

CAS: 28262-63-7

Fraction By Weight: >99%

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INGESTION: THERE IS NO INFORMATION ON
INGESTION TOXICITY OF "ELVACITE" 2013. INGESTION IS NOT PROBABLE
ROUTE OF EXPOS. TOX IS PREDICTED TO BE LOW. SKIN: THERE IS NO DATA
ON SKIN IRRIT OR SKIN SENSIT P ROPERTIES OF "ELVACITE" 2013.
HOWEVER, BASED ON INFO ON SIMILAR PRODUCTS, MAY CAUSE IRRITATION.
EYE: (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:HLTH HAZ: MECHANICAL IRRITATION ONLY.
INHALATION: GROSS OVEREXPOSURE TO NUISANCE PARTICLES, REGARDLESS OF
HOW GENERATED, MAY CAUSE IRRITATION OF THE RESPIRATORY TRACT.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:INHALATION: CONSULT PHYSICIAN IF NECESSARY. SKIN: FLUSH WITH
WATER AFTER CONTACT. WASH CONTAMINATED CLOTHING BEFORE REUSE. IF
MOLTEN POLYMER GETS ON SKIN, COOL RAPIDLY W/COLD WATER. DO NOT
ATTEMPT TO PEEL POLYMER FROM SKIN. OBTAIN MED TREATMENT FOR THERM
BURN. EYE: IMMED FLUSH W/PLENTY OF WATER FOR AT LEAST 15 MINUTES.
CALL PHYSICIAN. INGESTION: CONSULT PHYSICIAN IF NECESSARY.

Flash Point:572F,300C
Extinguishing Media:WATER, FOAM, DRY CHEMICAL, CARBON DIOXIDE.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:NO INFORMATION AVAILABLE.

Spill Release Procedures:NOTE: REVIEW FIRE AND EXPLOSION HAZARDS AND
SAFETY PRECAUTIONS BEFORE PROCEEDING WITH CLEAN UP. USE APPROPRIATE
PERSONAL PROTECTIVE EQUIPMENT DURING CLEAN UP. SHOVEL OR SWEEP UP.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:KEEP CONTAINER IN A COOL PLACE. CLOSE
CONTAINER AFTER EACH USE. GROUND CONTAINER WHEN POURING.
Other Precautions:NONE SPECIFIED BY MANUFACTURER.

Respiratory Protection:WEAR NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE
FOR EXPOSURE OF CONCERN .
Ventilation:GENERAL VENTILATION SUFFICIENT TO KEEP AIRBORNE
CONCENTRATION BELOW CURRENT EXPOSURE LIMITS .
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:LONG SLEEVE SHIRT.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
HAZARDOUS DECOMPOSITION PRODUCTS: ORGANIC ESTERS MAY BE GENERATED BY
DECOMPOSING POLYMER; THESE MAY CONTAIN METHACRYLATES. WASTE
DISPOSAL METHOD: FEDERAL, STATE/PROVINCIAL, AND LOCAL REGULATIONS.

HCC:N1
Decomp Temp:Decomp Text:392F,200C
Solubility in Water:NEGLIGIBLE
Appearance and Odor:BEADS, TYPICAL "METHACRYLATE" ODOR
Percent Volatiles by Volume:<1

Stability Indicator/Materials to Avoid:YES
NONE REASONABLY FORESEEABLE.
Stability Condition to Avoid:HEAT.
Hazardous Decomposition Products:DECOMP W/HEAT. DECOMP TEMP 200C.HAZ
GASES/VAPS PRDCED ARE CARBON MONOXIDE, ORG ACIDS, ALDEHYDES &
ALCOHOLS.SOME (SUPDAT)

Waste Disposal Methods:PREFERRED OPTIONS FOR DISP ARE (1) RECYCLING,
(2) INCIN W/ENERGY RECOVERY, & (3) LANDFILL. HIGH FUEL VALUE OF
PROD MAKES OPTION 2 VERY DESIRABLE FOR MATL THAT CANNOT BE
RECYCLED. TREATMENT, STORAGE, T RANSPORTATION,& DISP MUST BE I/A/W
APPLIC (SUPDAT)

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.